BELOW GROUND

 Piping 
 Sumps 
 Vents 

SHOWING ITEMS 1 - 12 OF 787 RESULTS
view_module view_list
$ 20.51
SBC-2100
The SBC eliminates the need to trim back the secondary jacket-and eliminates the need for rubber test boots.

• All Stainless Steel Wetted Surfaces
• No Jacket Stripping
• No Test Boots
• Male NPT Thread allows this coupling to be used with standard plumbing Tees and Elbows
• Decreased Installation Time
• Provides quick and effective means to monitor or retest secondary containment
• State-of-the-Art Clam Shell Interlock Design only available through OPW
• Double O-Ring Swivel Design for easy and secure connections
$ 161.32
70-0070
OPW Vertical Check Valves are installed on suction system fuel lines directly below the inlet to the pump in the dispenser island to maintain prime. The 70 Series Valves feature a built-in shear groove, which helps minimize piping damage if the dispenser is pulled over or dislodged by collision. The single-poppet provides redundant protection from losing prime and are also available without shear grooves. OPW Vertical Check Valves are recommended for use on suction lines where the pressure does not exceed 34 feet of head (approximately 15 psi [1 bar]). 70 Series valves need 1/2" of mercury to activate the poppet.

• Low Pressure Drop
• M-19 Viton Seals - on main poppet for compatibility with methanol-blended fuels and reliable sealing
• Protective Shear Groove - designed to reduce the possibility of damage to buried piping in the event the dispenser is knocked over
• Thermal Relief Valve - to reduce pressure build-up in suction pumps. Opens between 25 & 35 PSI (1.7 & 2.4 bar)
$ 74.99
SBC-2150
The SBC eliminates the need to trim back the secondary jacket-and eliminates the need for rubber test boots.

• All Stainless Steel Wetted Surfaces
• No Jacket Stripping
• No Test Boots
• Male NPT Thread allows this coupling to be used with standard plumbing Tees and Elbows
• Decreased Installation Time
• Provides quick and effective means to monitor or retest secondary containment
• State-of-the-Art Clam Shell Interlock Design only available through OPW
• Double O-Ring Swivel Design for easy and secure connections
$ 173.42
TBA-0150
FlexWorks™ Test Boots are used to isolate and air-test the interstitial space between the primary and secondary pipe. One test boot is required for each pipe end.
$ 16.36
DEB-0150
FlexWorks™ Double Flexible Entry Boots are designed to seal the sump penetration. These entry boots incorporate both internal and external band clamps to provide additional sealing in harsh environments. Boots firmly fasten and seal to the sump wall using steel studs, fasteners and a galvanized compression ring. These entry boots are available in a variety of sizes and designs to accommodate rigid and flexible piping, ducting and conduit.

• Watertight pipe and conduit entries
• Installation on flat or round surface
• Added flexibility permitting angled pipe entries
• Provides clean dry environment
• Accommodates various site installations
• Allows for easy field adjustments
• Can be repaired if damaged
• Third-party tested and approved
• Internal and external clamps for positive seal off
$ 61.14
DEB-4015A
FlexWorks™ Double Flexible Entry Boots are designed to seal the sump penetration. These entry boots incorporate both internal and external band clamps to provide additional sealing in harsh environments. Boots firmly fasten and seal to the sump wall using steel studs, fasteners and a galvanized compression ring. These entry boots are available in a variety of sizes and designs to accommodate rigid and flexible piping, ducting and conduit.

• Watertight pipe and conduit entries
• Installation on flat or round surface
• Added flexibility permitting angled pipe entries
• Provides clean dry environment
• Accommodates various site installations
• Allows for easy field adjustments
• Can be repaired if damaged
• Third-party tested and approved
• Internal and external clamps for positive seal off
$ 92.42
EBF-0150
FlexWorks™ Flexible Entry Boots are reliable, safe seals for pipe and conduit entries into underground containment sumps. These entry boots allow for angled pipe entries and have no exposed metal parts to the underground environment. These entry boots are available in a variety of sizes and designs to accommodate rigid and flexible piping, ducting and access pipe.

• Watertight pipe and conduit entries
• Installation on flat or round surface
• Added flexibility permitting angled entries up to 15 degrees
• 3rd Party Testing Approved
$ 37.36
70S-0075
OPW Vertical Check Valves are installed on suction system fuel lines directly below the inlet to the pump in the dispenser island to maintain prime. The 70 Series Valves feature a built-in shear groove, which helps minimize piping damage if the dispenser is pulled over or dislodged by collision. The single-poppet provides redundant protection from losing prime and are also available without shear grooves. OPW Vertical Check Valves are recommended for use on suction lines where the pressure does not exceed 34 feet of head (approximately 15 psi [1 bar]). 70 Series valves need 1/2" of mercury to activate the poppet.

The 70S series has some additional features, including the Stabilizer Mounting Bosses which are three bosses in the lower portion of the valve body to allow for rigid mounting to stabilizer bars. Use FlexWorks mounting plate with appropriate stabilizer bar kit. Also, a Built-In-Air-Test Port which allows air testing of the entire pumping system without breaking the line. Also allows line to be drained from the valve to the tank (assuming there are no other check or foot valves below the 70S).
$ 102.94
EBF-0751
FlexWorks™ Flexible Entry Boots are reliable, safe seals for pipe and conduit entries into underground containment sumps. These entry boots allow for angled pipe entries and have no exposed metal parts to the underground environment. These entry boots are available in a variety of sizes and designs to accommodate rigid and flexible piping, ducting and access pipe.

• Watertight pipe and conduit entries
• Installation on flat or round surface
• Added flexibility permitting angled entries up to 15 degrees
• 3rd Party Testing Approved
$ 36.34
DEB-0751
FlexWorks™ Double Flexible Entry Boots are designed to seal the sump penetration. These entry boots incorporate both internal and external band clamps to provide additional sealing in harsh environments. Boots firmly fasten and seal to the sump wall using steel studs, fasteners and a galvanized compression ring. These entry boots are available in a variety of sizes and designs to accommodate rigid and flexible piping, ducting and conduit.

• Watertight pipe and conduit entries
• Installation on flat or round surface
• Added flexibility permitting angled pipe entries
• Provides clean dry environment
• Accommodates various site installations
• Allows for easy field adjustments
• Can be repaired if damaged
• Third-party tested and approved
• Internal and external clamps for positive seal off
$ 59.13
$ 1.67